Nylon Tubing T/TIA Series

Download

Specifications of Nylon Tubing T/TIA Series

–	Tubing Size
	Metric size (T series)								Inch size (TIA series)
Nominal	T0425	T0403	T0604	T0645	T0806	T1075	T1209	T1613	TIA01	TIA05	TIA07	TIA11	TIA13
Outer diameter (mm)	4	4	6	6	8	10	12	16	3.18	4.76	6.35	9.53	12.7
Inner diameter (mm)	2.5	3	4	4.5	6	7.5	9	13	2.18	3.48	4.57	6.99	9.56

List Of Colors

• Black (B)
• White (W)
• Red (R)
• Blue (BU)
• Yellow (Y)
• Green (G)

Specifications

Fluid		Air, water
Maximum operating pressureNote 1)MPa	20°C or less	3.3	2.0	3.0	2.0	2.0	2.0	2.0	1.6	2.3	2.3	2.3	2.3	2.3
	40°C	2.3	1.4	2.1	1.4	1.4	1.4	1.4	1.1	1.6	1.6	1.6	1.6	1.6
	60°C	1.65	1.0	1.5	1.0	1.0	1.0	1.0	0.8	1.15	1.15	1.15	1.15	1.15
	80°C	1.35	0.8	1.25	0.8	0.8	0.8	0.8	0.65	0.95	0.95	0.95	0.95	0.95
	100°C	1.2	0.75	1.1	0.75	0.75	0.75	0.75	0.6	0.85	0.85	0.85	0.85	1.85
Applicable fittingsNote 1) Note 2)		One-touch fittings, insert fittings, self-align fittings, miniature fittings
Minimum bending radius mmNote 3)	Minimum bending radius	13	20	24	30	40	50	60	100	15	25	30	50	65
	Tube close bend radius (reference value)	10	15	18	23	30	40	45	75	12	20	23	40	48
Operating temperatureNote 1)		-40 to +100°C, Water: 0 to +70℃ (No freezing)
Material		Nylon 12

Note 1) Be sure to operate under the maximum operating pressure and maximum operating temperature conditions using the lower maximum operating specification of either the tubing or fittings.
Note 2) Mount an inner sleeve when using metal one-touch fittings in high-temperature environments of 60°C or more.
Use self-align fittings at a temperature of 60°C or less.
Note 3) The minimum bending radius is the representative value measured as shown in the figure on the left (“How to measure the minimum bending radius”).

• Use a tube above the recommended minimum bending radius.
• The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the refraction value and make sure that the tubing is not bent or flattened.
• The tube close bend radius is not guaranteed. The value of 2R is a representative value measured with a bent or flattened tube using the method shown in the figure on the left.

How to measure the minimum bending radius

Made-To-Order Specifications

• 100‑m reel: Metric size and inch size, except for ø16 (diameter 16 mm). Suffix “-X3” to the end of part number.
• Longer length reel: Metric size. Suffix “-X3” to the end of part number.
• 20‑m roll: Inch size. Suffix “-X4” to the end of part number.

* Please contact SMC for specifications in detail, dimensions, delivery and specifications other than those mentioned above.

Caution

• 1. Applicable for general industrial water. Please consult with SMC if using other kinds of fluid. Also, the surge pressure must not exceed the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to fittings and tubes.
• 2. Please exercise caution when using this item in a clean room. There is a possibility of plasticizers and other materials precipitating on the tube surface and detracting from the cleanliness level of the room.

* See the manufacturer’s catalog for safety information.