Brushless Motors BXII Series – Động cơ không chổi than

Wide Speed Control Range 2~4000 r/min

Achieved speed ratio of 1:2000.

  Suitable for applications that require constant torque from low to high speeds.
(30~4000 r/min at analog setting.)

Stable Motor Drive

Speed Regulation ±0.05 %

Reduces speed variation due to changes in the load (load fluctuation) and the change of ambient environment (changing ambient temperature, voltage fluctuation).

Flutter Characteristics Effective Value: Approx. 0.1 %

The effective value of the flutter characteristics, which represents speed fluctuations of motor rotation, is about 0.1 %. (Reference value at rated speed)
Even when rotating at a certain speed, there will be slight fluctuation in the actual speed around the target rotation speed. The speed fluctuations are known as flutter.

Supports Multi-Speed Operation with Up to 16 Speeds

Up to 16 points of operation data, such as operating speed and acceleration/deceleration time, can be set.

Operation and Switch Up to 16 Data Points With Just I/O

You can set up to 16 points of operation data such as travel amount and operating speed.

Linking Multiple Operation Data

In addition to single data setting, you can also set linked operation, which combines multiple operation data.

• *Dwell time is the wait time until the next positioning operation starts.

Continuous Rotation in the Same Direction is Possible

The command position and multiple rotation data can be returned to 0 if the command position exceeds the “wrap setting range” parameter value. Since the multiple rotation data is returned to 0, continuous rotation in the same direction is possible.

All models can be selected with or without an electromagnetic brake. The electromagnetic brake is automatically controlled to turn ON/OFF according to the operation command signal to the driver.

Capable of Vertical Operation (Gravitational operation)

With an electromagnetic brake, stable speed control is possible even when driving vertical operation.

During vertical operation, regenerative energy is generated. Use a regeneration resistor (Sold separately).

Capable of Position Holding When Stopped

Position holding when driving in a vertical direction^* or horizontal direction is possible.
When driving horizontally, it is possible to set servo lock at motor standstill, which excites the motor to generate a holding force.

• *For vertical operation (gravitational operation), use a product with an electromagnetic brake.

Prevents Loads From Falling in an Emergency

The electromagnetic brake is of the power off activated type, so it works automatically even when power is lost in a blackout. Instantly stops the motor and prevents the load from falling.

It can be used for applications that require adjustment of torque and tension, such as tension (brake), pushing (pressing), and tightening.

• Tension – As a Brake to Gain Tension

  

• Pushing – For Printing and Other Press Applications

  

The setting range of the maximum instantaneous torque of the motor can be limited from 0 to 250 % in 1 % units.

• Torque limiting accuracy ±10 % approx. (relative to rated torque)
• Torque limiting can be switched ON/OFF with an external signal (TL input)

Easy Setting and Start-Up With MEXE02 Support Software

By using the support software MEXE02, you can set and edit operation data and various parameters, as well as teach and monitor various conditions.

Comprehensive Support From Start-Up to Maintenance With a Variety of Functions

• Startup and Evaluation

  Useful functions for wiring check and test operation are provided.

  • Setting and Saving of Operation Data
  • I/O Monitor
  • Teaching, Remote Operation
• Adjustment

  The following functions are available to help you adjust motor operation after the equipment is installed.

  • Waveform Monitor
• Diagnosis and Maintenance

  Diagnostic and maintenance functions are available for trouble diagnosis and maintenance after operation is started.

  • Alarm Monitor
  • Status Monitor
  • Warning Monitor

Click here for details on support software functions

On-Site Monitoring and Troubleshooting are Also Possible

Speed and alarm information can be monitored on the driver’s display screen. Data setting and test operation are also possible at the operation panel.

If the OPX-2A control module is connected, operation becomes even easier.

Compact Driver for Close Installation to Reduce Installation Space.

Optimized arrangement of internal parts has made the drivers compact and slim. It also supports close installation of multiple units, further reducing installation space.

Gearhead Type

Gearhead Types	Parallel Shaft Gearhead	Hollow Shaft Flat Gearhead
	GFS Gearhead	FR Gearhead
External View
Features	Steel Shaft Wide Range of Gear Ratio	Space Saving, Cost Saving High Permissible Torque
Output Power	30 W, 60 W, 120 W 200 W, 400 W	30 W, 60 W, 120 W 200 W, 400 W
Gear Ratio	5~200	5~200
Rated Life	10000 hours	10000 hours
Permissible Radial Load*	1400 N	2040 N
Permissible Axial Load*	400 N	800 N
Permissible Torque*	70 N·m	54 N·m

• *This value is for output power of 200 W, 3000 r/min, and the maximum gear ratio.

Significantly Increases Permissible Load Flange Drive Adapter (Sold separately)

Mounting on a parallel shaft gearhead increases permissible radial and axial loads.

Refer to here for more information.