Brushless Motor Offering a Wider Selection

Output Power

15 W/30 W/50 W/100 W

Motor Type

• Connector type/Lead wire type (IP40)
• Cable type (IP65)
• Electromagnetic brake motor (IP65)

Output Shaft Type

3 Selectable Driver Types

• 

  Analog setting type

  • Speed setting with potentiometer
  • I/O control of stop operation

• 

  Digital setting type

  • Speed setting using support software
  • I/O control of stop operation

• 

  RS-485 Communication Type

  • Speed setting with Modbus protocol
  • Monitoring from the host controller possible

Compact, lightweight, board type

Fine speed settings and excellent speed regulation ratios allow for different types of operation.

Reduced Equipment Takt Time

Reduces takt time by shortening starting and deceleration time.

There are Two Main Factors That Reduce Takt Time in the Equipment

①

Starting Time Reduction
Maximum instantaneous torque (1.5 times rated torque) reduces starting time

②

Stop Time Reduction
Deceleration stop time can be set to be shorter.

Selecting Deceleration Stop Methods (Digital Setting Type and RS-485 Communication Type)

Generates brake force at a deceleration stop and stops in accordance with an arbitrarily set time.
The deceleration stop operation can be set on the MEXE02 support software.

Torque Adjustment (Digital setting type, RS-485 communication type)

A torque limiting function is provided to reduce the torque generated by the motor.
The range of maximum instantaneous torque can be set from 0 to 200 %, with 100 % at the rated torque.
The MEXE02 support software also allows you to monitor the load factor and output information at an arbitrarily set threshold (torque value).

Applications

• Adjusting the tightening force
• Pressurization in pressing applications (Pushing)
• · Preventing damage from pinching (Low thrust)
• Adjustment of gripping force

Suitable for Quiet Environments

By reviewing the drive method of driver allowed us to achieve a lower noise level compared to conventional products.

Comparison of Driving Noise Between Conventional and Upgraded Products (With driving noise)

Simultaneous Speed Operation (Digital setting type, RS-485 communication type)

Digital setting allows speed to be set in 1 r/min increments, enabling multiple motors to operate at the same speed. You can operate multiple units at the same speed, such as running 2 conveyors side by side or running an automatic guided vehicle (AGV).

Generates a Holding Force When an External Force is Applied, Load Holding Function (Digital setting type, RS-485 communication type)

It can be used as an electrical holding brake^* when stopping without a mechanical brake.

• *Holding loads up to 50 % of rated torque.

Advantages of No Mechanical Brake Mechanism

• Long life with no maintenance required due to non-wear parts
• Minimizing space usage and weight of the equipment

Note

If the power supply to the driver is turned off, the holding force dissipates. This cannot be used to prevent a fall when stopped.

Applications

Applications that frequently start and stop

Direct Connection via a Single Cable, No Relay Required (Connector type)

1 Rank Higher Output Power (Connector type)

• One Rank Higher Output Power at the Same Mounting Angle (Frame Size:42 mm)

  

• Model Number 1 is More Compact With the Same Output Power (Output Power: 30 W)

  

Standstill and Holding by Electromagnetic Brake Electromagnetic Brake Motor

The electromagnetic brake motor can hold the position during horizontal driving.
It can hold the stop position when stopping the equipment to reload or process workpieces, or hold the load in the event of blackout or other unforeseen circumstances.

Note

This product is not suitable for usages requiring vertical movement, such as gravitational operations.

Confirm Motor Stop by MOVE Output (Digital setting type, RS-485 communication type)

The MOVE output can be used to check when to turn off the electromagnetic brake.

Gearheads Selectable According to the Application Brushless Motors BLH Series

Gearhead Type	Parallel Shaft Gearhead		Hollow Shaft Flat Gearhead
	GFS Gearhead	CS Geared Motor	FR Gearhead
External View
Features	Wide range of gear ratios Rated life of 10000 hours*	Increased load capacity center shaft Rated life of 10000 hours	Space saving, cost saving Unsaturated permissible torque Rated life of 10000 hours
Motor Output Power	15 W/30 W/50 W/100 W	15 W/30 W/50 W	30 W/50 W/100 W
Gear Ratio	5~200	5~20	5~200

• *The 15 W unit has a rated life of 5000 hours.

Significantly Increases Permissible Load Flange Drive Adapter (Sold separately)

Mounting on a parallel shaft gearhead increases permissible radial and axial loads.

Useful Functions Utilizing Support Software MEXE02

By using the support software MEXE02, you can set and edit operation data and various parameters, as well as teach and monitor various conditions.

Comprehensive Support From Start-Up to Maintenance With a Variety of Functions

• Startup and Evaluation

  Useful functions for wiring check and test operation are provided.

  • Setting and Saving of Operation Data
  • I/O Monitor
  • Teaching, Remote Operation
• Adjustment

  The following functions are available to help you adjust motor operation after the equipment is installed.

  • Waveform Monitor
• Diagnosis and Maintenance

  Diagnostic and maintenance functions are available for trouble diagnosis and maintenance after operation is started.

  • Alarm Monitor
  • Status Monitor
  • Information Monitor

RS-485 communication can be used to set operation data and parameters, as well as input operation commands. The Modbus (RTU) protocol is used.

Easy to Set and Change Operation Data and Save Wiring

Remote and Ongoing Monitoring Enabled